Asus WL-330gE

QDSL-1040WU высокопроизводительный универсальный шлюз доступа, обеспечивающий подключение к IP-сети с использованием технологии ADSL2+ или Ethernet. Шлюз предназначен для использования в сетях широкополосного доступа xDSL или FTTx. Широкий набор функций маршрутизации и встроенная точ-ка доступа Wi-Fi 802.11n обеспечивает возможность использования устройства как маршрутизатора для небольшой сети. USB-порт шлюза позволяет использовать 3G модем для подключения к сети Интернет. Поддерживается работа в сетях 2G/3Gи СDMA (СкайЛинк).

Ключевые возможности:

ADSL2/2+ и Ethernet-маршрутизатор; Встроенная точка доступа 802.11 b/g/n; WPA/WPA-2; WMM; Один из портов LAN-может использоваться как WAN-порт, для подключения к сети Ethernet/PON; VPN Pass-Through; IP QOS; IGMP Proxy; До 16 PVC; Статическая маршрутизация; Резервирование канала при использовании 3G-модема; Родительский контроль; Загрузка и выгрузка конфигурации; TR-069/TR-098/TR-104/TR-111. Оф. Сайт http://www.qtech.ru/catalog/archadsl/171/chars.htm

chaos_calmer 15.05, initial test, WIFI is randomly disappeared, https://downloads.openwrt.org/chaos_calmer/15.05/brcm47xx/legacy/openwrt-15.05-brcm47xx-legacy-asus-wl-330ge-squashfs.trx

1. → downloads
2. → Install OpenWrt
3. → Latest OpenWrt release

Please check out the article flash.layout. It contains an example and a couple of explanations.

The instructions below are for Broadcom devices and only serve as an example. Don't leave them in place if they do not apply to a particular device!

This section deals with how you install OpenWrt from a device freshly opened. Plus the steps required such as reset to factory defaults if the device has already been configured

Note: Reset router to factory defaults if it has been previously configured.

• Browse to http://192.168.1.1/Upgrade.asp
• Upload .bin file to router
• Wait for it to reboot
• Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

→ generic.flashing.tftp

→ generic.sysupgrade

If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

• Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
• Upload image file for sysupgrade to LuCI
• Wait for reboot

• Login as root via SSH on 192.168.1.1
• Use the following commands to upgrade.

cd /tmp/
wget http://http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

• If sysupgrade does not support this router, use the following commands.

cd /tmp/
wget http://http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

The default network configuration is:

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

→ failsafe_and_factory_reset

→ hardware.button on howto use and configure the hardware button(s).

The Linksys WRT54GL has two buttons. They are Reset and Secure Easy Setup. Here, we merely name the buttons, so we can use them in the above Howto:

Model Number

Front:

Photo of front of the casing

Back:

Photo of back of the casing

→ Warranty

• To remove the cover do a/b/c

Main PCB

Photo of PCB

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Photo of PCB with markings

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:

Photo of PCB with markings

→ generic.debrick

1. you could read about bootloader in general

1. as a beginner, you really should inform yourself about soldering in general and then obtain some practical experience!

How to add tags