D-Link DIR-810L

D-Link DIR-810L

The DIR-810L AC750 Wireless Dual-Band Router uses the MT7620A SoC, with 802.11bgn (SoC-integrated) and 802.11ac (on-board) radios.

OEM source code is available by searching for 810L at: https://tsd.dlink.com.tw/dlist?OS=GPL

The board is similar to TRENDnet TEW-810DR

Supported Versions

Hardware Highlights

In a 2023 snapshot build, 5 GHz radio was not working (including after a hard reboot) until setting 40 MHz bandwidth, Saving, changing the channel, Saving, then switching back to 80 MHz bandwidth, and Applying.

Installation

→ Install OpenWrt (generic explanation)

Flashing OpenWrt over factory firmware

Later router revisions (e.g. B1 and F/W 2.03b02) don't have an open bootloader, and there is also no factory image available.

To create a factory image with Linux, the correct signature needs to be appended to the end of the sysupgrade file with a tool found in the GPL toolchain download from D-Link.

These are the necessary steps in Linux (for Windows see https://learn.microsoft.com/en-us/windows/wsl/install):

Download the SDK by searching for 810L at https://tsd.dlink.com.tw/dlist?OS=GPL using the applicable hardware version. Firmware version shouldn't matter as the tool should be the same for all versions
extract the tarball in the src subdirectory
extract the ncc_att_hwid tool (in source/user/wolf/cameo/ncc/hostTools/) to /tmp
Download the DIR-810L sysupgrade image to /tmp
modify the image e.g.: ./ncc_att_hwid -f /tmp/{firmware} -m DIR-810L -H B1 -r WW -c 1.0 -F 2.03b02 -a
...where {firmware} is the downloaded sysupgrade.bin e.g. openwrt-22.03.5-ramips-mt7620-dir-810l-sysupgrade.bin
change the '-r {region}' as needed e.g. '-r US'

A previous note (using Chaos Calmer) said “Recovery mode wouldn't accept it but the normal factory web interface does”. However, the above worked fine in Recovery mode with a snapshot build (DD-WRT was the active firmware). Note: '-F 2.04b01' was used as it was the latest OEM firmware installed, but not sure if that matters.

Hardware

Photos

Serial port

The D-Link DIR-810L features a TTL serial port. You can use a TTL to USB adaptor to connect to it. The following image shows the pin location. There's no need to connect Vcc.

Settings: 57600 8N1

Bootloader

U-Boot 1.1.3 (Jan  7 2013 - 16:08:08)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83f98000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29 
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D

MAC: c8:d3:a3:64:ce:0a
============================================ 
Ralink UBoot Version: 4.1.1.0
DIR-810L(1.00b03)
-------------------------------------------- 
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan  7 2013  Time:16:08:08
============================================ 
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768 

 ##### The CPU freq = 580 MHZ #### 
 estimate memory size =64 Mbytes

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial. 
   9: Load Boot Loader code then write to Flash via TFTP. 
 0 
   
3: System Boot system code via Flash.
## Booting image at bc170000 ...
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    5976005 Bytes =  5.7 MB
   Load Address: 80000000
   Entry Point:  8000c2d0
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

No initrd
## Transferring control to Linux (at address 8000c2d0) ...
## Giving linux memsize in MB, 64

Version 2.0.16-b51

/proc/mtd

# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 00800000 00010000 "ALL"
mtd1: 00030000 00010000 "Bootloader"
mtd2: 00010000 00010000 "Config"
mtd3: 00010000 00010000 "Factory"
mtd4: 00010000 00010000 "5G_RF"
mtd5: 00010000 00010000 "Wolf_Config"
mtd6: 00080000 00010000 "MyDLink"
mtd7: 00080000 00010000 "Jffs2"
mtd8: 000f8f8d 00010000 "Kernel"
mtd9: 00597073 00010000 "RootFS"
mtd10: 00690000 00010000 "Kernel_RootFS"

Bootlogs

Original firmware V1.0.1

Starting kernel ... LINUX started... THIS IS ASIC init started: BusyBox v1.12.1 (2013-03-28 15:33:49 CST) starting pid 35, tty '': '/etc_ro/rcS' mount: mounting none on /proc/bus/usb failed: No such file or directory Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= mount mydlink ok mount flash ok old language pack not found language pack exists Starting loop GPIO LED=9,PBC=2 Waiting for Wireless Events from interfaces... [ leobox_ipc.c: 207 sem_create()]:::add semid = 0 [ leobox_ipc.c: 207 sem_create()]:::add semid = 32769 [ leobox_ipc.c: 207 sem_create()]:::add semid = 65538 [ leobox_ipc.c: 207 sem_create()]:::add semid = 98307 [ leobox_ipc.c: 207 sem_create()]:::add semid = 131076 [ leobox_ipc.c: 207 sem_create()]:::add semid = 163845 [ leobox_ipc.c: 207 sem_create()]:::add semid = 196614 [ leobox_ipc.c: 207 sem_create()]:::add semid = 229383 [ leobox_ipc.c: 207 sem_create()]:::add semid = 262152 [ leobox_ipc.c: 207 sem_create()]:::add semid = 294921 [ leobox_ipc.c: 207 sem_create()]:::add semid = 327690 [ leobox_ipc.c: 207 sem_create()]:::add semid = 360459 [ leobox_ipc.c: 207 sem_create()]:::add semid = 393228 [ leobox_ipc.c: 207 sem_create()]:::add semid = 425997 [ leobox_ipc.c: 207 sem_create()]:::add semid = 458766 [ leobox_ipc.c: 207 sem_create()]:::add semid = 491535 [ leobox_ipc.c: 207 sem_create()]:::add semid = 524304 [ leobox_ipc.c: 207 sem_create()]:::add semid = 557073 [ leobox_ipc.c: 207 sem_create()]:::add semid = 589842 [ leobox_ipc.c: 207 sem_create()]:::add semid = 622611 [ leobox_ipc.c: 207 sem_create()]:::add semid = 655380 [ 122 ncc_main.c : 177 main()]:::[122]Thread Create[main thread] [ 122 ncc_runtimecfg.c : 432 initRunTimeCfg()]:::Init Run-Time Config Success. [ 122 ncc_runtimecfg.c : 433 initRunTimeCfg()]:::Total 4342 nodes, each node 24 bytes. [ 122 ncc_runtimecfg.c : 434 initRunTimeCfg()]:::Total 104208 byte for all nodes. [ 122 ncc_runtimecfg.c : 435 initRunTimeCfg()]:::Total 63953 byte for data. [ 122 ncc_runtimecfg.c : 153 loadCfg()]:::Start loadCfg [ 122 ncc_lz77.c : 534 flash2rootfs()]:::Load Success(/var/tmp/cfg.txt) ================nice=-20 starting pid 145, tty '/dev/ttyS1': '/bin/sh' # [ 122 ncc_lz77.c : 628 rootfs2flash()]:::write header KBLA,32548 [ 122 ncc_lz77.c : 633 rootfs2flash()]:::write data 32548 [ 122 ncc_lz77.c : 646 rootfs2flash()]:::write sync done [ 122 ncc_inf.c : 605 ncc_inf_main()]:::JTraceLevel=4 [ 122 leobox_network.c : 1064 socket_select()]:::Enter pid=122,ppid=1 [leobox_network.c: 1074 socket_select()]:::main process get thread id=1026 [ 149 ncc_inf.c : 432 processInf()]:::[149]Thread Create[processInf] [ 148 leobox_network.c : 816 socket_select_hdlr()]:::[148]Thread Create[socket_select_hdlr] bind: Address already in use [ 122 ncc_main.c : 269 main()]:::Stop Web Access HTTP [ 122 ncc_httpd.c : 539 httpdOp()]:::st is null. [ 122 /opt/release/RT288x_SDK_0214/RT288x_SDK/source/user/wolf/cameo/ncc/../model/dlink_810/objTools/ncc_objTools.c: 5036 probeHTTPsEnable()]:::probeHTTPsEnable(); [ 122 ncc_main.c : 291 main()]:::Start HTTPS mini_httpd: started as root without requesting chroot(), warning only sh: cannot create /sys/class/net/br0/bridge/tcp_allow: nonexistent directory bind: Address already in use [ 122 ncc_main.c : 305 main()]:::Stop Web Access HTTPS [ 122 ncc_httpd.c : 539 httpdOp()]:::st is null. mini_httpd: started as root without requesting chroot(), warning only [ 162 ncc_main.c : 41 sendBootEvent()]:::[162]Thread Create[sendBootEvent] [ 161 leobox_timer.c : 248 timerThread()]:::[161]Thread Create[timerThread] [ 161 leobox_timer.c : 256 timerThread()]:::Timer Thread Running sh: cannot create /proc/sys/net/ipv4/conf/eth2.2/arp_ignore: nonexistent directory [ 122 ncc_fsm_boot.c : 513 Boot()]:::=====================Start DIR_810_Boot===================== [ 122 ncc_fsm_boot.c : 570 Boot()]:::MAC 0 = C8D3A364CE0A [ 122 ncc_fsm_boot.c : 571 Boot()]:::MAC 1 = C8D3A364CE0B switch reg write offset=3100, value=56330 switch reg write offset=3200, value=56330 switch reg write offset=3300, value=56330 switch reg write offset=3400, value=56330 switch reg write offset=3000, value=56330 Set: phy[4].reg[4] = 05e1 Set: phy[4].reg[0] = 3300 [ 122 ncc_l2_independence.c: 171 swSpeedSet()]:::port = 4, speed = 0 killall: crond: no process killed [ 122 ncc_crond.c : 54 crondConf()]:::DEBUG ON [ 122 ncc_firewall.c : 1601 reBuildMAC6()]:::reBuildMAC6()+ [ 122 ncc_firewall.c : 1629 reBuildMAC6()]:::reBuildMAC6()- ip6tables: No chain/target/match by that name. killall: wakeOnLanProxy: no process killed [ 122 ncc_firewall.c : 4672 runFwScript()]:::===ipt run start=== ### WOL CONFIG: No such file or directory [ 122 ncc_firewall.c : 4674 runFwScript()]:::===ipt run end=== [ 122 ncc_fsm_boot.c : 780 Boot()]:::cfg->tzone=128 Sat Jan 1 00:00:00 GMT 2011 [ 122 ncc_fsm_boot.c : 806 Boot()]:::Merge language pack!! [ 4242 lang_merge.c : 1125 main()]:::before print info [ 4242 lang_merge.c : 1128 main()]:::Parameters: ori_lang_fp: /var/tmp/lang.js def_lang_fp: /www/def_lang.js [ 4242 lang_merge.c : 1196 main()]:::save to old js file!! [ 4242 lang_merge.c : 1197 main()]:::save to old js file!! [ 4242 lang_merge.c : 1198 main()]:::save to old js file!! sh: cannot create /proc/sys/net/ipv6/conf/ra1/disable_ipv6: nonexistent directory sh: cannot create /proc/sys/net/ipv6/conf/rai1/disable_ipv6: nonexistent directory [ 122 ncc_help.c : 1268 checkDefCfg()]:::defCfg=1 llmnr: have no available linklocal address. wait count=0 [ 122 ncc_firewall.c : 4672 runFwScript()]:::===ipt run start=== [ 122 ncc_firewall.c : 4674 runFwScript()]:::===ipt run end=== [ 122 ncc_firewall.c : 4672 runFwScript()]:::===ipt run start=== llmnr: have no available linklocal address. wait count=1 [ 122 ncc_firewall.c : 4674 runFwScript()]:::===ipt run end=== llmnr: have no available linklocal address. wait count=2 mDNSResponderPosix: Starting in daemon mode killall: lld2d: no process killed ***** g_wl_interface = ra0 ****** killall: proxy: no process killed [ leobox_ipc.c: 207 sem_create()]:::add semid = 688149 [ 6008 lanmapd.c : 2646 main()]:::=============================Lanmapd============================= [ 6008 lanmapd.c : 2647 main()]:::iface br0 [ 6008 lanmapd.c : 2648 main()]:::ip 192.168.0.1 [ 6008 lanmapd.c : 2652 main()]:::netmask 255.255.255.0 [ 6008 lanmapd.c : 2653 main()]:::network id 192.168.0.0 [ 6008 lanmapd.c : 2654 main()]:::mac c8:d3:a3:64:ce:0a [ 6008 lanmapd.c : 2655 main()]:::hostname dlinkrouter [ 6008 lanmapd.c : 2656 main()]:::hostname encode EEEMEJEOELFCEPFFFEEFFCCACACACAAA [ 6008 lanmapd.c : 2661 main()]:::================================================================= killall: crond: no process killed llmnr: have no available linklocal address. wait count=3 killall: wscd: no process killed Starting loop GPIO LED=9,PBC=2 [ 122 ncc_fsm_boot.c : 307 doRtInit()]:::Send Event to open 2.4G Wlan ! [ 122 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched llmnr: have no available linklocal address. wait count=4 llmnr: have no available linklocal address. wait count=5 llmnr: have no available linklocal address. wait count=6 llmnr: have no available linklocal address. wait count=7 llmnr: have no available linklocal address. wait count=8 llmnr: have no available linklocal address. wait count=9 [ 122 ncc_fsm_boot.c : 312 doRtInit()]:::Send Event to open 5G Wlan ! [ 122 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched llmnr: have no available linklocal address. wait count=10 llmnr: have no available linklocal address. wait count=11 llmnr: have no available linklocal address. wait count=12 Starting loop GPIO LED=9,PBC=2 killall: wscd: no process killed libupnp: using UDP SSDP_PORT = 1900 brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy Interface doesn't accept private ioctl... set (8BE2): Invalid argument Interface doesn't accept private ioctl... set (8BE2): Invalid argument Starting loop GPIO LED=9,PBC=2 route: ioctl 0x890b failed: File exists [ 122 ncc_fsm_boot.c : 920 Boot()]:::wanCableLink = 0 mDNSResponderPosix: Starting in daemon mode [ 122 ncc_dev_independence.c: 3757 devOpFunc()]:::get internet_cable_lose [ 122 ncc_firewall.c : 4672 runFwScript()]:::===ipt run start=== llmnr: have no available linklocal address. wait count=13 [ 122 ncc_firewall.c : 4674 runFwScript()]:::===ipt run end=== ip6tables: Bad rule (does a matching rule exist in that chain?). llmnr: have no available linklocal address. wait count=14 [ 122 ncc_help.c : 1621 is_v6defaultgw_exist()]:::[IPv6 WARNING] Default GW not Exist. [ 122 ncc_radvd.c : 233 radvdConf()]:::is6rdsunset: 0, prefix: [ 122 ncc_fsm_boot.c : 1296 Boot()]:::setting v6Lan Host Filter=fe80:0:0:0:cad3:a3ff:fe64:ce0b! [ 122 ncc_fsm_boot.c : 1318 Boot()]:::=====================finish DIR_810_Boot===================== [SYS][ 122 ncc_fsm_boot.c : 1333 Boot()]:::Boot Complate!! [ 122 ncc_EventInternal.c : 1128 doEventInternal()]:::InternalLocalTimeChange [ 122 ncc_EventInternal.c : 498 onMailSchedule()]:::mailCfg.schedSendEnable ? 0 [ 122 ncc_EventInternal.c : 1147 doEventInternal()]:::needSendLog = 0 brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy

OpenWrt Barrier Breaker 14.07rc2

Starting kernel ... [ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41795) ) #3 Mon Jul 28 18:38:34 CEST 2014 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is D-Link DIR-810L [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00066eb0 [ 0.000000] Readback ErrCtl register=00066eb0 [ 0.000000] Memory: 61376k/65536k available (2519k kernel code, 4160k reserved, 609k data, 196k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 512 [ 0.070000] pinctrl core: initialized pinctrl subsystem [ 0.080000] NET: Registered protocol family 16 [ 0.460000] bio: create slab <bio-0> at 0 [ 0.470000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.480000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.490000] PCI host bridge to bus 0000:00 [ 0.500000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.510000] pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff] [ 0.520000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.530000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] [ 0.540000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 0.550000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] [ 0.560000] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 0.570000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.570000] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] [ 0.580000] Switching to clocksource MIPS [ 0.590000] NET: Registered protocol family 2 [ 0.590000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.600000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.610000] TCP: Hash tables configured (established 512 bind 512) [ 0.630000] TCP: reno registered [ 0.630000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.640000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.660000] NET: Registered protocol family 1 [ 0.670000] rt-timer 10000100.timer: maximum frequncy is 2441Hz [ 0.700000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.710000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.730000] msgmni has been set to 119 [ 0.740000] io scheduler noop registered [ 0.740000] io scheduler deadline registered (default) [ 0.750000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.770000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 0.790000] console [ttyS0] enabled, bootconsole disabled [ 0.790000] console [ttyS0] enabled, bootconsole disabled [ 0.820000] m25p80 spi32766.0: mx25l6405d (8192 Kbytes) [ 0.830000] 8 ofpart partitions found on MTD device spi32766.0 [ 0.840000] Creating 8 MTD partitions on "spi32766.0": [ 0.850000] 0x000000000000-0x000000030000 : "u-boot" [ 0.860000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.870000] 0x000000040000-0x000000050000 : "factory" [ 0.880000] 0x000000050000-0x000000060000 : "factory5g" [ 0.900000] 0x000000060000-0x000000070000 : "Wolf_Config" [ 0.910000] 0x000000070000-0x0000000f0000 : "MyDlink" [ 0.920000] 0x0000000e0000-0x000000160000 : "Jffs2" [ 0.930000] 0x000000170000-0x000000800000 : "firmware" [ 0.940000] 0x00000028003e-0x000000800000 : "rootfs" [ 0.950000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.980000] mtd: device 8 (rootfs) set to be root filesystem [ 0.990000] mtd: partition "rootfs_data" created automatically, ofs=0x4a0000, len=0x360000 [ 1.010000] 0x0000004a0000-0x000000800000 : "rootfs_data" [ 1.020000] gsw: setting port4 to ephy mode [ 1.030000] (unregistered net_device): port 0 link up (100Mbps/Full duplex) [ 1.050000] ralink_soc_eth 10100000.ethernet: loaded mt7530 driver [ 1.060000] eth0: done loading [ 1.070000] rt3xxx-usbphy ubsphy.3: loaded [ 1.080000] rt2880_wdt 10000120.watchdog: Initialized [ 1.090000] TCP: cubic registered [ 1.090000] NET: Registered protocol family 17 [ 1.100000] Bridge firewalling registered [ 1.110000] 8021q: 802.1Q VLAN Support v1.8 [ 1.130000] VFS: Mounted root (squashfs filesystem) readonly on device 31:8. [ 1.150000] Freeing unused kernel memory: 196K (8030f000 - 80340000) procd: Console is alive procd: - watchdog - [ 4.570000] usbcore: registered new interface driver usbfs [ 4.580000] usbcore: registered new interface driver hub [ 4.590000] usbcore: registered new device driver usb [ 4.610000] leds-gpio gpio-leds.5: pins are not configured from the driver procd: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level jffs2 is ready jffs2 is ready [ 7.290000] jffs2: notice: (313) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 11 of xref (0 dead, 2 orphan) found. switching to overlay procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 8.630000] NET: Registered protocol family 10 [ 8.650000] nf_conntrack version 0.5.0 (962 buckets, 3848 max) [ 8.670000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 8.690000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea [ 8.700000] Backport generated by backports.git backports-20140320-37-g5c33da0 [ 8.720000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 8.770000] xt_time: kernel timezone is -0000 [ 8.800000] cfg80211: Calling CRDA to update world regulatory domain [ 8.810000] cfg80211: World regulatory domain updated: [ 8.820000] cfg80211: DFS Master region: unset [ 8.830000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 8.850000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 8.870000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 8.880000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 8.900000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A) [ 8.910000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 8.930000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 8.950000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 8.960000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 9.040000] PPP generic driver version 2.4.2 [ 9.060000] NET: Registered protocol family 24 [ 9.100000] rt2800_wmac 10180000.wmac: failed to load eeprom property [ 9.110000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'. procd: Could not[ 9.160000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM. find firmware /[ 9.180000] rt2800_wmac: probe of 10180000.wmac failed with error -2 lib/firmware/soc_wmac.eeprom procd: - init complete - [ 15.600000] device eth0.1 entered promiscuous mode [ 15.610000] device eth0 entered promiscuous mode [ 15.620000] br-lan: port 1(eth0.1) entered forwarding state [ 15.630000] br-lan: port 1(eth0.1) entered forwarding state [ 17.630000] br-lan: port 1(eth0.1) entered forwarding state BusyBox v1.22.1 (2014-07-22 12:47:56 CEST) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (14.07-rc2, r41815) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/#

Table of Contents