Meraki MR30H

The Meraki MR30H is a POE powered Cisco AP with 4 downstream Gigabit Ethernet ports. Unfortunately, the flashing process is quite cumbersome.

Serial interface (pin out details below)

Read the full guide before proceeding and make sure you understand the requirements before proceeding.

Built on Ubuntu 18.04 LTS, this guide assumes you have a basic working knowledge of the command line and know your way around permissions, copying files etc.

Links are provided as additional reading and guidance.

Compile Your Own Build (optional)

These devices were “cloud-connected” with automatic upgrades and therefore most devices will be running the latest Cisco firmware. The Flash Method to use depends on the version of the Bootloader present. First determine the version of U-Boot on your device:

  1. Open the device by unscrewing the 4 screws under the rubber pads with a Torx T5 screwdriver.
  2. Connect to the serial console. (Refer to Serial and Serial Console for more info.)
  3. Power on the device, the Bootloader version is displayed immediately upon booting.

Please use the table below to find out which flash method to use:

Architecture ARMv7
Vendor Qualcomm
Bootloader U-boot
System-On-Chip IPQ4029
CPU Speed 700MHz
Flash-Chip Spansion
Flash size 128MiB
RAM 256 MiB DDR3
Wireless IPQ4029, QCA9889
Switch QCA8075
Ethernet ports 5x Gigabit, port 4 802.3af POE output
USB No
Serial Yes
JTAG No
Comments

port.serial general information about the serial port, serial port cable, etc.

The UART is 3.3V, 115200 baud, on header J8. The header is already soldered.

1: Vcc (DO NOT CONNECT)
2: TX
3: RX
4: GND
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00096 S - IMAGE_VARIANT_STRING=DAACANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000025 S - Core 0 Frequency, 0 MHz B - 261 - PBL, Start B - 1339 - bootable_media_detect_entry, Start B - 2612 - bootable_media_detect_success, Start B - 2626 - elf_loader_entry, Start B - 4036 - auth_hash_seg_entry, Start B - 6190 - auth_hash_seg_exit, Start B - 73814 - elf_segs_hash_verify_entry, Start B - 194360 - PBL, End B - 194384 - SBL1, Start B - 283060 - pm_device_init, Start D - 6 - pm_device_init, Delta B - 284585 - boot_flash_init, Start D - 87395 - boot_flash_init, Delta B - 376030 - boot_config_data_table_init, Start D - 13980 - boot_config_data_table_init, Delta - (419 Bytes) B - 392708 - clock_init, Start D - 7564 - clock_init, Delta B - 403677 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1 B - 407163 - sbl1_ddr_set_params, Start B - 412148 - cpr_init, Start D - 2 - cpr_init, Delta B - 416638 - Pre_DDR_clock_init, Start D - 5 - Pre_DDR_clock_init, Delta D - 13141 - sbl1_ddr_set_params, Delta B - 429918 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 500602 - sbl1_wait_for_ddr_training, Start D - 27 - sbl1_wait_for_ddr_training, Delta B - 516129 - Image Load, Start D - 140680 - QSEE Image Loaded, Delta - (262104 Bytes) B - 657307 - Image Load, Start D - 2117 - SEC Image Loaded, Delta - (2048 Bytes) B - 667467 - Image Load, Start D - 123135 - APPSBL Image Loaded, Delta - (285640 Bytes) B - 791025 - QSEE Execution, Start D - 56 - QSEE Execution, Delta B - 797207 - SBL1, End D - 604903 - SBL1, Delta S - Flash Throughput, 1995 KB/s (550211 Bytes, 275770 us) S - DDR Frequency, 672 MHz U-Boot 2017.07-RELEASE-g78ed34f31579 (Sep 29 2017 - 07:43:44 -0700) DRAM: 242 MiB machid : 0x8010001 Product: meraki_Noisy_Cricket NAND: ONFI device found ID = 1d80f101 Vendor = 1 Device = f1 128 MiB Using default environment In: serial Out: serial Err: serial machid: 8010001 ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=0", size 115 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 920, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 7, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 8/3, WL threshold: 4096, image sequence number: 1374043440 ubi0: available PEBs: 350, total reserved PEBs: 570, PEBs reserved for bad PEB handling: 20 Read 0 bytes from volume part.safe to 84000000 No size specified -> Using max size (2375680) ## Loading kernel from FIT Image at 84000000 ... Using 'config@2' configuration Trying 'kernel@1' kernel subimage Description: Insects Kernel Type: Kernel Image Compression: uncompressed Data Start: 0x840000f4 Data Size: 1733064 Bytes = 1.7 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: sha1 Hash value: 17b99ce0147e4b39500a929ccbd526d29009431f Verifying Hash Integrity ... sha1+ OK ## Loading ramdisk from FIT Image at 84000000 ... Using 'config@2' configuration Trying 'ramdisk@1' ramdisk subimage Description: Insect Ramdisk Type: RAMDisk Image Compression: uncompressed Data Start: 0x841a73a8 Data Size: 526520 Bytes = 514.2 KiB Architecture: ARM OS: Linux Load Address: 0x82200000 Entry Point: 0x82200000 Hash algo: sha1 Hash value: ef74c36ec4b6523dd8591ba5cb5f657ed39218d1 Verifying Hash Integrity ... sha1+ OK Loading ramdisk from 0x841a73a8 to 0x82200000 ## Loading fdt from FIT Image at 84000000 ... Using 'config@2' configuration Trying 'fdt@2' fdt subimage Description: MR30H Device Tree Type: Flat Device Tree Compression: uncompressed Data Start: 0x84230d04 Data Size: 37636 Bytes = 36.8 KiB Architecture: ARM Hash algo: sha1 Hash value: fba9954420659f38e9735271dfb97dd67b2456ed Verifying Hash Integrity ... sha1+ OK Loading fdt from 0x84230d04 to 0x89000000 Booting using the fdt blob at 0x89000000 Loading Kernel Image ... OK Using Device Tree in place at 89000000, end 8900c303 Using machid 0x8010001 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.14.79 (jenkins@dal247.meraki.com) (gcc version 4.8.3 (GCC) ) #1 SMP PREEMPT Thu Dec 14 18:00:33 PST 2017 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Meraki MR30H [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 7 pages/cpu @cfcc9000 s7360 r8192 d13120 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 61954 [ 0.000000] Kernel command line: console=ttyMSM0,115200n8 maxcpus=1 ubi.mtd=ubi clk_ignore_unused [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 241284K/249856K available (3320K kernel code, 315K rwdata, 1204K rodata, 151K init, 549K bss, 8572K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0000000 - 0xff000000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xcff00000 ( 255 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0673538 (4526 kB) [ 0.000000] .init : 0xc0674000 - 0xc0699cc0 ( 152 kB) [ 0.000000] .data : 0xc069a000 - 0xc06e8e00 ( 316 kB) [ 0.000000] .bss : 0xc06e8e0c - 0xc077242c ( 550 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] Architected cp15 timer(s) running at 48.00MHz (virt). [ 0.000009] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 2863311552512ns [ 0.000018] Switching to timer-based delay loop [ 0.000262] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000280] pid_max: default: 32768 minimum: 301 [ 0.000533] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000547] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.012022] CPU: Testing write buffer coherency: ok [ 0.012371] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.012441] Setting up static identity map for 0x80525e58 - 0x80525eb0 [ 0.070010] Brought up 1 CPUs [ 0.070027] SMP: Total of 1 processors activated (96.00 BogoMIPS). [ 0.070035] CPU: All CPU(s) started in SVC mode. [ 0.070624] devtmpfs: initialized [ 0.080389] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.081018] pinctrl core: initialized pinctrl subsystem [ 0.081940] regulator-dummy: no parameters [ 0.083822] NET: Registered protocol family 16 [ 0.085308] DMA: preallocated 2048 KiB pool for atomic coherent allocations [ 0.087432] cpuidle: using governor ladder [ 0.087447] cpuidle: using governor menu [ 0.104761] No ATAGs? [ 0.104850] [ 0.104850] Version Rollback Feature Disabled [ 0.106587] Error: Driver 'msm8x74-pinctrl' is already registered, aborting... [ 0.110304] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2 [ 0.111970] i2c-msm-v2 78b8000.i2c: probing driver i2c-msm-v2 [ 0.114288] sps:sps is ready. [ 0.126402] bio: create slab <bio-0> at 0 [ 0.129024] SD0 VccQ: 1800 <--> 3000 mV [ 0.132112] msm_bus_fabric_init_driver [ 0.132291] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 [ 0.132308] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 [ 0.132327] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1 [ 0.132373] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 [ 0.132387] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 [ 0.132404] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1 [ 0.173429] Bluetooth: Core ver 2.18 [ 0.173636] NET: Registered protocol family 31 [ 0.173648] Bluetooth: HCI device and connection manager initialized [ 0.173668] Bluetooth: HCI socket layer initialized [ 0.173683] Bluetooth: L2CAP socket layer initialized [ 0.173751] Bluetooth: SCO socket layer initialized [ 0.173962] 80000.qcom,pcie supply vreg-3.3 not found, using dummy regulator [ 0.174026] 80000.qcom,pcie supply vreg-1.8 not found, using dummy regulator [ 0.174078] 80000.qcom,pcie supply vreg-0.9 not found, using dummy regulator [ 0.174128] 80000.qcom,pcie supply gdsc-vdd not found, using dummy regulator [ 0.270502] msm_pcie_enable: msm_pcie_enable: PCIe: trigger the reset of endpoint of RC0. [ 0.280453] msm_pcie_enable: msm_pcie_enable: PCIe RC0 PHY is ready! [ 0.300450] msm_pcie_enable: msm_pcie_enable: PCIe: Release the reset of endpoint of RC0. [ 0.440554] msm_pcie_enable: msm_pcie_enable: PCIe RC0 link initialized [ 0.440957] PCI host bridge to bus 0000:00 [ 0.440986] pci_bus 0000:00: root bus resource [io 0x40200000-0x402fffff] [ 0.441003] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff] [ 0.441018] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.441104] msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0014[4] is all FFs [ 0.441696] PCI: bus0: Fast back to back transfers disabled [ 0.441717] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.442157] msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 1:0x00 + 0x0014[4] is all FFs [ 0.442889] PCI: bus1: Fast back to back transfers disabled [ 0.442985] msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0028[4] is all FFs [ 0.443020] pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff] [ 0.443039] pci 0000:00:00.0: BAR 9: assigned [mem 0x40300000-0x403fffff pref] [ 0.443057] pci 0000:00:00.0: BAR 0: assigned [mem 0x40600000-0x40600fff 64bit] [ 0.443088] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit] [ 0.443130] pci 0000:01:00.0: BAR 6: assigned [mem 0x40300000-0x4030ffff pref] [ 0.443145] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.443166] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] [ 0.443184] pci 0000:00:00.0: bridge window [mem 0x40300000-0x403fffff pref] [ 0.443204] msm_pcie_probe: msm_pcie_probe: RC0 is enabled in bootup [ 0.443541] Switched to clocksource arch_sys_counter [ 0.447597] NET: Registered protocol family 2 [ 0.448663] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.448710] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.448762] TCP: Hash tables configured (established 2048 bind 2048) [ 0.448826] TCP: reno registered [ 0.448843] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.448875] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.449208] NET: Registered protocol family 1 [ 0.450105] Unpacking initramfs... [ 0.789811] Freeing initrd memory: 512K (c2200000 - c2280000) [ 0.793007] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.806515] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.806568] msgmni has been set to 472 [ 0.808354] io scheduler noop registered [ 0.808368] io scheduler deadline registered (default) [ 0.809748] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 [ 0.809815] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.809890] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.809958] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.811474] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.813244] msm_serial_hsl_probe: detected port #0 (ttyMSM0) [ 0.813285] msm_serial_hsl_probe: Bus scaling is disabled [ 0.813446] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 139, base_baud = 115200) is a MSM [ 0.813522] msm_hsl_console_setup: console setup on port #0 [ 1.546287] console [ttyMSM0] enabled [ 1.550624] msm_serial_hsl_probe: detected port #1 (ttyMSM1) [ 1.555687] msm_serial_hsl_probe: Bus scaling is disabled [ 1.561074] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 140, base_baud = 115200) is a MSM [ 1.570422] msm_serial_hsl_init: driver initialized [ 1.575079] msm_serial_hs module loaded [ 1.578773] Trying to register dev faulty etc [ 1.583097] at24 0-0050: 8192 byte 24c64 EEPROM, writable, 32 bytes/write [ 1.591728] sps: BAM device 0x07984000 is not registered yet. [ 1.596576] sps:BAM 0x07984000 is registered. [ 1.600612] msm_nand_bam_init: msm_nand_bam_init: BAM device registered: bam_handle 0xcf97dc00 [ 1.609645] sps:BAM 0x07984000 (va:0xd0260000) enabled: ver:0x19, number of pipes:7 [ 1.617285] msm_nand_version_check: nand_major:1, nand_minor:4, qpic_major:1, qpic_minor:4 [ 1.625347] msm_nand_scan: missing page size info - extract from NAND ID [ 1.631949] msm_nand_scan: NAND Id: 0x1d80f101 Buswidth: 8Bits Density: 128 MByte [ 1.639453] msm_nand_scan: pagesize: 2048 Erasesize: 131072 oobsize: 64 (in Bytes) [ 1.646978] msm_nand_scan: BCH ECC: 4 Bit [ 1.650966] msm_nand_scan: CFG0: 0x2a0408c0, CFG1: 0x0804745c [ 1.650966] RAWCFG0: 0x280420c0, RAWCFG1: 0x0005045d [ 1.650966] ECCBUFCFG: 0x00000203, ECCBCHCFG: 0x42040700 [ 1.650966] BAD BLOCK BYTE: 0x000001d1 [ 1.673707] 12 ofpart partitions found on MTD device 7980000.qcom,nand [ 1.680122] Creating 12 MTD partitions on "7980000.qcom,nand": [ 1.685959] 0x000000000000-0x000000100000 : "sbl1" [ 1.693364] 0x000000100000-0x000000200000 : "mibib" [ 1.699728] 0x000000200000-0x000000300000 : "bootconfig" [ 1.706566] 0x000000300000-0x000000400000 : "qsee" [ 1.712784] 0x000000400000-0x000000500000 : "qsee_alt" [ 1.719564] 0x000000500000-0x000000580000 : "cdt" [ 1.725396] 0x000000580000-0x000000600000 : "cdt_alt" [ 1.731602] 0x000000600000-0x000000680000 : "ddrparams" [ 1.738234] 0x000000700000-0x000000900000 : "u-boot" [ 1.745454] 0x000000900000-0x000000b00000 : "u-boot-backup" [ 1.753283] 0x000000b00000-0x000000b80000 : "ART" [ 1.759330] 0x000000c00000-0x000007c00000 : "ubi" [ 1.845018] msm_nand_probe: NANDc phys addr 0x7980000, BAM phys addr 0x7984000, BAM IRQ 133 [ 1.852339] msm_nand_probe: Allocated DMA buffer at virt_addr 0xd023c000, phys_addr 0x8f8fe000 [ 1.862295] libphy: ipq40xx_mdio: probed [ 1.869284] ipq40xx-mdio 90000.mdio: ipq40xx-mdio driver was registered [ 1.875932] input: gpio_keys.7 as /devices/soc.0/gpio_keys.7/input/input0 [ 1.882303] i2c /dev entries driver [ 1.888029] ina2xx 1-0040: power monitor ina226 (Rshunt = 12500 uOhm) [ 1.894234] qcom_wdt b017000.watchdog: boot reason:0 [ 1.899408] Bluetooth: HCI UART driver ver 2.2 [ 1.902820] Bluetooth: HCI H4 protocol initialized [ 1.973573] lp5562 1-0030: internal clock used [ 1.984670] meraki-config board-data.9: Meraki config device loaded [ 1.990299] TCP: cubic registered [ 1.993206] NET: Registered protocol family 17 [ 1.997771] Registering SWP/SWPB emulation handler [ 2.004555] SD0 VccQ: disabling [ 2.006665] regulator-dummy: disabling [ 2.011157] UBI: attaching mtd11 to ubi0 [ 2.493266] UBI: scanning is finished [ 2.505962] UBI: attached mtd11 (name "ubi", size 112 MiB) to ubi0 [ 2.511111] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 2.517942] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 2.524685] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 2.531421] UBI: good PEBs: 896, bad PEBs: 0, corrupted PEBs: 0 [ 2.537360] UBI: user volume: 7, internal volumes: 1, max. volumes count: 128 [ 2.544478] UBI: max/mean erase counter: 8/3, WL threshold: 4096, image sequence number: 1374043440 [ 2.553471] UBI: available PEBs: 326, total reserved PEBs: 570, PEBs reserved for bad PEB handling: 20 [ 2.562788] UBI: background thread "ubi_bgt0d" started, PID 544 [ 2.581527] /mnt/jenkins/workspace/router/prod-router_25-gerrit/BOARD/insect/label/FW-PROD/linux-3.14/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.598086] clk: Not disabling unused clocks [ 2.601509] devtmpfs: mounted [ 2.605069] Freeing unused kernel memory: 148K (c0674000 - c0699000) [ 2.611370] random: init: uninitialized urandom read (4 bytes read, 0 bits of entropy available) [ 2.619964] Made it into bootsh: Dec 14 2017 17:59:20 [ 2.624493] bootsh build 25-201712141532-G0bb86dd3-hamaki [ 2.643325] mknod_from_sysfs_entry: error creating /dev/mtdchar/ART(90:34 ): File exists [ 2.650791] mknod_from_sysfs_entry: error creating /dev/mtdblock/ART(31:17 ): File exists [ 2.673582] UBIFS: background thread "ubifs_bgt0_1" started, PID 576 [ 2.693353] UBIFS: recovery needed [ 2.786780] UBIFS: recovery completed [ 2.789520] UBIFS: mounted UBI device 0, volume 1, name "storage" [ 2.795516] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 2.804620] UBIFS: FS size: 15618048 bytes (14 MiB, 123 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) [ 2.814164] UBIFS: reserved for root: 737678 bytes (720 KiB) [ 2.819801] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 8DBC1CAC-F7D8-4C46-B1A1-473D4C821F30, small LPT model [ 2.841659] sps: BAM device 0x07884000 is not registered yet. [ 2.846475] sps:BAM 0x07884000 is registered. [ 2.850656] sps:BAM 0x07884000 (va:0xd0a00000) enabled: ver:0x19, number of pipes:12 In manufacturing: FALSE In rma mode: FALSE [ 2.886825] Bootsh: trying rootfs path: /dev/mtdblock/rootfs-25-201712141532-G0bb86dd3-hamaki-1 Attempting to setup root /dev/mtdblock/rootfs-25-201712141532-G0bb86dd3-hamaki-1... [ 4.205187] copy_directory: Skipping /ro/etc/lighttpd.conf.ssl st_mode = 21b6 [ 5.310493] init started: BusyBox v1.24.1 (2017-12-14 17:37:56 PST) [ 5.422923] Sat Jan 1 00:00:00 UTC 2000 [ 6.798283] random: board_data_conf: uninitialized urandom read (4 bytes read, 45 bits of entropy available) [ 6.810043] random: serial_loginche: uninitialized urandom read (4 bytes read, 45 bits of entropy available) WARNING! THIS CONSOLE IS LOGGED! UNAUTHORIZED ACCESS FORBIDDEN! <Meraki> [ 6.946786] sysctl: error: 'vm.extfrag_threshold' is an unknown key [ 7.091125] 377+0 records in [ 7.092979] 377+0 records out [ 7.096128] 12064 bytes (11.8KB) copied, 0.095017 seconds, 124.0KB/s [ 7.310840] 377+0 records in [ 7.312692] 377+0 records out [ 7.315836] 12064 bytes (11.8KB) copied, 0.087585 seconds, 134.5KB/s [ 7.421190] 377+0 records in [ 7.423045] 377+0 records out [ 7.426189] 12064 bytes (11.8KB) copied, 0.093113 seconds, 126.5KB/s [ 7.577646] QCE50: __qce_init_clk: Unable to get CE core src clk, set to NULL [ 7.586849] qcrypto 8e20000.qcrypto: Qualcomm Crypto 5.3.1 device found @0x8e20000 [ 7.593401] qcrypto 8e20000.qcrypto: CE device = 0x0 [ 7.593401] , IO base, CE = 0xd20c0000 [ 7.593401] , Consumer (IN) PIPE 2, Producer (OUT) PIPE 3 [ 7.593401] IO base BAM = 0x (null) [ 7.593401] BAM IRQ 239 [ 7.593401] Engines Availability = 0x2010453 [ 7.627592] sps:BAM 0x08e04000 is registered. [ 7.631757] sps:BAM 0x08e04000 (va:0xd2100000) enabled: ver:0x27, number of pipes:4 [ 7.639592] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000008e04000 irq 239 [ 7.646586] bus_scale_table is NULL [ 7.649831] qcrypto 8e20000.qcrypto: qcrypto-ecb-aes [ 7.654861] qcrypto 8e20000.qcrypto: qcrypto-cbc-aes [ 7.659696] qcrypto 8e20000.qcrypto: qcrypto-ctr-aes [ 7.664661] qcrypto 8e20000.qcrypto: qcrypto-rfc3686-ctr-aes [ 7.670285] qcrypto 8e20000.qcrypto: qcrypto-ecb-des [ 7.675251] qcrypto 8e20000.qcrypto: qcrypto-cbc-des [ 7.680179] qcrypto 8e20000.qcrypto: qcrypto-ecb-3des [ 7.685250] qcrypto 8e20000.qcrypto: qcrypto-cbc-3des [ 7.690256] qcrypto 8e20000.qcrypto: qcrypto-xts-aes [ 7.695225] qcrypto 8e20000.qcrypto: qcrypto-sha1 [ 7.699884] qcrypto 8e20000.qcrypto: qcrypto-sha256 [ 7.704773] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-aes [ 7.710995] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-des [ 7.717272] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-3des [ 7.723633] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-aes [ 7.729987] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-des [ 7.736479] qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-3des [ 7.742938] qcrypto 8e20000.qcrypto: qcrypto-aes-ccm [ 7.747902] qcrypto 8e20000.qcrypto: qcrypto-rfc4309-aes-ccm [ 7.753418] qcrypto: FIPS140-2 Known Answer Tests: Skipped [ 9.876756] edma module_init [ 10.064046] reset ok in probe! [ 11.644378] PSGMII recovered after 0 times reset [ 11.654132] EDMA using MAC@ - using 86:70:5f:df:9c:00 [ 11.724121] EDMA using MAC@ - using 7e:24:f5:6c:72:5f [ 11.847658] EDMA using MAC@ - using a2:f8:83:f8:2e:92 [ 11.970243] EDMA using MAC@ - using 9e:58:61:5d:37:80 [ 12.087081] EDMA using MAC@ - using 7a:25:be:0c:b8:e5 [ 12.910662] random: board_data_conf: uninitialized urandom read (4 bytes read, 59 bits of entropy available) [ 12.980760] random: board_data_conf: uninitialized urandom read (4 bytes read, 59 bits of entropy available) [ 13.050745] random: board_data_conf: uninitialized urandom read (4 bytes read, 59 bits of entropy available) [ 13.120711] random: board_data_conf: uninitialized urandom read (4 bytes read, 59 bits of entropy available) [ 13.170169] random: board_data_conf: uninitialized urandom read (4 bytes read, 59 bits of entropy available) [ 13.417663] random: ccloader: uninitialized urandom read (4 bytes read, 59 bits of entropy available) [ 13.654266] autobaud successful [ 13.657835] dummy cmd result: 0x41 [ 13.660767] Chip id: 80 00 f0 00 [ 13.663502] test successful [ 13.902630] random: nonblocking pool is initialized [ 14.035184] CRC32: 5f 5c ae 70 [ 14.041208] file CRC32: 5f5cae70 [ 14.048947] firmware load successful [ 15.503149] sysctl -w vm.panic_on_oom=2 [ 15.512435] vm.panic_on_oom = 2 [ 16.448583] click: starting router thread pid 1006 (cf205e00) [ 17.936034] elts_meraki: module license 'unspecified' taints kernel. [ 17.941360] Disabling lock debugging due to kernel taint [ 18.146002] Single synchronous check for reset [ 18.649542] [ 18.660439] boot 21 build 25-201712141532-G0bb86dd3-hamaki board insect mac E0:CB:BC:26:D2:1A [ 18.679507] Module: qcrypto .text=0xbf000000 .data=0xbf006d48 .bss=0xbf0081a8 [ 18.679507] Module: essedma .text=0xbf011000 .data=0xbf0180a4 .bss=0xbf018544 [ 18.679507] Module: dummy .text=0xbf01f000 .data=0xbf01f434 .bss= [ 18.679507] Module: proclikefs .text=0xbf023000 .data= .bss=0xbf023b00 [ 18.679507] Module: merakiclick .text=0xbf028000 .data=0xbf11f448 .bss=0xbf11f6c0 [ 18.679507] Module: elts_meraki .text=0xbf225000 .data=0xbf484670 .bss=0xbf485ce0 [ 18.679507] Module: reed_solomon .text=0xbf629000 .data=0xbf62a370 .bss= [ 18.971918] ramoops: using module parameters [ 18.979334] pstore: Registered ramoops as persistent store backend [ 18.999572] ramoops: attached 0x100000@0x8ff00000, ecc: 0/0 [ 19.013062] ls -1 /sys/fs/pstore/dmesg-ramoops-* 2>/dev/null [ 19.033908] /usr/bin/check_bootreason: reading file : No such file or directory [ 19.057510] ln: /usr/bin/slowfcgi: File exists [ 20.514001] ath_spectral: Version 2.0.0 [ 20.514001] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved [ 20.882998] ath_hal: 0.9.17.1 (AR9380, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D) [ 20.911701] ath_dfs: Version 2.0.0 [ 20.911701] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved [ 21.801911] ol_ath_ahb_probe [ 21.807370] ol_ath_ahb_probe: io resource start: 0xa000000, mem=0xd3000000 [ 21.813219] *********** Dakota ************* [ 21.827737] __ol_ath_attach: Creating netdev wifi0 [ 21.831786] [ 21.831786] __ol_ath_attach() Allocated scn cd2804c0 [ 21.838689] ol_ath_ahb_configure: MSI addr: 0b006040, MSI base: 00000040 [ 21.845161] ath10k_ahb a000000.wifi: ath DEBUG: sc=0xcdc1c800 [ 21.850336] [ 21.850336] ol_ath_ahb_configure : num_desired MSI set to 0 [ 21.858233] [ 21.858233] Using Legacy Interrupt [ 21.862403] [ 21.862403] Waiting for target init [ 21.868159] [ 21.868159] Done waiting [ 21.874447] [ 21.874447] CLOCK PLL skipped [ 21.878163] __ol_ath_attach: dev name wifi0 [ 21.882208] ol_ath_attach interface_id 0 [ 21.887001] ol_target_init() BMI inited. [ 21.890258] ol_target_init() BMI Get Target Info. [ 21.895171] Chip id: 0xb, chip version: 0x1000000 [ 21.899390] [ 21.899390] CE WAR Disabled [ 21.904622] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 21.909730] ol_target_init() configure Target . [ 21.914219] [ 21.914219] Target Version is 1000000 [ 21.918835] [ 21.918835] Flash Download Address c0000 [ 21.925148] ol_transfer_bin_file: flash data file defined [ 21.929863] ol_transfer_bin_file[3752] Get Caldata for wifi0. [ 21.936033] __adf_os_fs_read[42], Open File /tmp/wifi0.caldata SUCCESS!! [ 21.942272] file system magic:16914836 [ 21.946528] super blocksize:4096 [ 21.949390] inode 1154 [ 21.951819] file size:12064 [ 21.955302] ol_transfer_bin_file 3813: Download Flash data len 12064 [ 21.961450] Board extended Data download address: 0x0 [ 21.986164] [ 21.986164] Board data initialized [ 21.990268] ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 [ 21.998208] [ 21.998208] Selecting OTP binary for CHIP Version 0 [ 22.513125] ol_transfer_bin_file 3623: downloading file 0, Download data len 4424 [ 22.536444] [ 22.536444] First OTP send param 8000 [ 22.545447] ol_ath_download_firmware :First OTP download and Execute is good address:0x5000 return param 4660 [ 22.554678] ol_ath_download_firmware:##Board Id 20 , CHIP Id 0 [ 22.560316] ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 [ 22.567500] [ 22.567500] wifi0: Selecting board data file name boardData_1_0_IPQ4019_DK04_2G.bin [ 22.576759] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/mr30h/boardData_1_0_IPQ4019_DK04_2G.bin [ 22.589410] ol_transfer_bin_file 3623: downloading file 3, Download data len 12064 [ 22.597193] Board extended Data download address: 0x0 [ 22.621406] ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 22.627683] [ 22.627683] Selecting OTP binary for CHIP Version 0 [ 22.634495] ol_transfer_bin_file 3623: downloading file 0, Download data len 4424 [ 22.657174] [ 22.657174] [Flash] : Ignore Module param [ 22.661715] [ 22.661715] Second otp download Param 10000 [ 22.678544] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 [ 22.686038] [ 22.686038] Mission mode: Firmware CHIP Version 0 [ 22.693234] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 [ 22.704557] Swap: bytes_left to copy: fw:16; dma_page:109113 [ 22.709188] Swap: wrong length read:0 [ 22.712835] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 153031 Target address 4172b0 [ 22.722688] scn=cd2804c0 target_write_addr=4172b0 seg_info=cdcc1510 [ 22.728422] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 [ 22.737165] bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin [ 22.747340] ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin [ 22.757095] ol_transfer_bin_file 3623: downloading file 1, Download data len 364076 [ 23.983582] ol_target_init() Download FW done. [ 23.987156] ol_ath_attach() WMI attached. wmi_handle ce4a0000 [ 23.992928] htc_wmi_init() HT Create . cd2d0000 [ 23.998160] htc_wmi_init() HIF Claim. [ 24.001248] htc_wmi_init 7732 host_enable 0 nss_nwifi_offload 0 [ 24.007400] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) [ 24.016624] OL_ACBKMinfree : 0 [ 24.019463] OL_ACBEMinfree : 0 [ 24.022586] OL_ACVIMinfree : 0 [ 24.026233] OL_ACVOMinfree : 0 [ 24.033363] CE_recv_buf_enqueue 877 Populate last entry 512 for CE 5 [ 24.038762] CE_recv_buf_enqueue 886 CE 5 wi 511 dest_ptr 0x8dd53ac0 nbytes 0 recv_ctxt 0xce4e4c00 [ 24.048897] Startup Mode-0 set [ 24.050923] [ 24.050923] <=== cfg max peer id 1056 ====> [ 24.057637] HTC Service:0x0300 ep:1 TX flow control disabled [ 24.062588] htt_peer_map_timer_init Enter pdev ce5b8000 hrtimer ce5ba520 [ 24.069526] [ 24.069526] htt_alloc_peer_map_mem : Alloc Success : host q vaddr ceeb0000 paddr 8eeb0000 [ 24.079105] [ 24.079105] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 24.089985] CE_pkt_dl_len_set CE 4 Pkt download length 64 [ 24.094949] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from ccfa0000 [ 24.103369] HTC Service:0x0100 ep:2 TX flow control disabled [ 24.109730] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 24.115791] Firmware_Build_Number:92 [ 24.119135] num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffa [ 24.129032] [ 24.129032] RES CFG Support wmi_service_bitmap 9778 [ 24.136136] Sending Ext resource cfg: HOST PLATFORM as 0 and fw_feature_bitmap as 50 to TGT [ 24.144276] ol_ath_service_ready_event: tt_support: 1 [ 24.149254] ol_ath_service_ready_event: periodic_chan_stats: 1 [ 24.155760] ol_ath_service_ready_event: sw_cal_support_check_flag: 1 [ 24.161412] Peer Caching Enabled ; num_peers = 257, num_active_peers = 52 num_tids = 104, num_vdevs = 17 [ 24.171441] Mesh Supported [ 24.173839] idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 [ 24.181325] ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, [ 24.189173] idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 [ 24.196877] ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, [ 24.204380] idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 [ 24.212095] ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, [ 24.219885] idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 258 [ 24.227604] ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 258 unit_len 744, [ 24.235016] idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 [ 24.242762] ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, [ 24.250599] idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 [ 24.258130] ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144, [ 24.265564] idx 6 req 5 num_units 0 num_unit_info 2 unit size 2044 actual units 258 [ 24.273190] ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 86 unit_len 2044, [ 24.281172] ol_ath_alloc_host_mem_chunk req_id 5 idx 7 num_units 86 unit_len 2044, [ 24.288562] ol_ath_alloc_host_mem_chunk req_id 5 idx 8 num_units 86 unit_len 2044, [ 24.295964] chunk 0 len 13568 requested ,ptr 0x8cf6c000 [ 24.301080] chunk 1 len 54272 requested ,ptr 0x8c000000 [ 24.306838] chunk 2 len 217088 requested ,ptr 0x8c040000 [ 24.311931] chunk 3 len 191952 requested ,ptr 0x8c080000 [ 24.317774] chunk 4 len 107520 requested ,ptr 0x8c020000 [ 24.322866] chunk 5 len 6144 requested ,ptr 0x8cf98000 [ 24.328530] chunk 6 len 175784 requested ,ptr 0x8c0c0000 [ 24.333876] chunk 7 len 175784 requested ,ptr 0x8c100000 [ 24.339099] chunk 8 len 175784 requested ,ptr 0x8c140000 [ 24.345078] ol_ath_service_ready_event[4067] WAPI MBSSID 2 [ 24.386824] wmi_ready_event_rx: WMI UNIFIED READY event [ 24.391217] ol_ath_connect_htc() WMI is ready [ 24.395699] htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 0 [ 24.410988] ol_ath_attach() connect HTC. [ 24.414008] target uses HTT version 2.2; host uses 2.2 [ 24.419465] bypasswmi : 0 [ 24.421694] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 24.434509] acfg_attach: 2892: Netlink socket created:cdc1e800 [ 24.439342] SPECTRAL : get_capability not registered [ 24.445009] HAL_CAP_PHYDIAG : Capable [ 24.447902] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) [ 24.456402] SPECTRAL : get_capability not registered [ 24.460919] HAL_CAP_RADAR : Capable [ 24.464953] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 24.464953] (spectral_attach : 242) [ 24.474779] SPECTRAL : get_capability not registered [ 24.479322] HAL_CAP_SPECTRAL_SCAN : Capable [ 24.483490] SPECTRAL : get_tsf64 not registered [ 24.488522] spectral_init_netlink 78 NULL SKB [ 24.492351] Green-AP : Green-AP : Attached [ 24.492351] [ 24.498498] Green-AP : Attached [ 24.501024] rate power table override is only supported for AR98XX [ 24.508244] ol_if_dfs_attach: called; ptr=cc0b1984, radar_info=cdf69c48 [ 24.514267] dfs_attach: event log enabled by default [ 24.520060] ipq4019_wifi_led_init: Wifi LED init failed.. Couldn't get led gpio/led source [ 24.529216] ol_ath_attach() UMAC attach . [ 24.532281] [ 24.532281] BURSTING enabled by default [ 24.539002] ACS not enabled [ 24.540855] __ol_ath_attach: needed_headroom reservation 60 [ 24.554396] ol_ath_thermal_mitigation_attach: -- [ 24.565437] ol_ath_ahb_probe [ 24.567359] ol_ath_ahb_probe: io resource start: 0xa800000, mem=0xd3400000 [ 24.600215] *********** Dakota ************* [ 24.604053] __ol_ath_attach: Creating netdev wifi1 [ 24.608605] [ 24.608605] __ol_ath_attach() Allocated scn cc2404c0 [ 24.615399] ol_ath_ahb_configure: MSI addr: 0b006040, MSI base: 00000050 [ 24.621697] ath10k_ahb a800000.wifi: ath DEBUG: sc=0xcc20c000 [ 24.627756] [ 24.627756] ol_ath_ahb_configure : num_desired MSI set to 0 [ 24.634760] [ 24.634760] Using Legacy Interrupt [ 24.639221] [ 24.639221] Waiting for target init [ 24.644946] [ 24.644946] Done waiting [ 24.655148] [ 24.655148] CLOCK PLL skipped [ 24.659824] __ol_ath_attach: dev name wifi1 [ 24.662975] ol_ath_attach interface_id 1 [ 24.667722] ol_target_init() BMI inited. [ 24.670993] ol_target_init() BMI Get Target Info. [ 24.675941] Chip id: 0xb, chip version: 0x1000000 [ 24.680158] [ 24.680158] CE WAR Disabled [ 24.685388] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 24.690500] ol_target_init() configure Target . [ 24.698259] [ 24.698259] Target Version is 1000000 [ 24.702450] [ 24.702450] Flash Download Address c0000 [ 24.708791] ol_transfer_bin_file: flash data file defined [ 24.713478] ol_transfer_bin_file[3752] Get Caldata for wifi1. [ 24.719678] __adf_os_fs_read[42], Open File /tmp/wifi1.caldata SUCCESS!! [ 24.726160] file system magic:16914836 [ 24.729705] super blocksize:4096 [ 24.733005] inode 1156 [ 24.735981] file size:12064 [ 24.738369] ol_transfer_bin_file 3813: Download Flash data len 12064 [ 24.745491] Board extended Data download address: 0x0 [ 24.769343] [ 24.769343] Board data initialized [ 24.773443] ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 [ 24.781398] [ 24.781398] Selecting OTP binary for CHIP Version 0 [ 24.787889] ol_transfer_bin_file 3623: downloading file 0, Download data len 4424 [ 24.810886] [ 24.810886] First OTP send param 8000 [ 24.820287] ol_ath_download_firmware :First OTP download and Execute is good address:0x5400 return param 4660 [ 24.829436] ol_ath_download_firmware:##Board Id 21 , CHIP Id 0 [ 24.835439] ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 [ 24.841933] [ 24.841933] wifi1: Selecting board data file name boardData_1_0_IPQ4019_DK04_5G.bin [ 24.851688] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/mr30h/boardData_1_0_IPQ4019_DK04_5G.bin [ 24.864240] ol_transfer_bin_file 3623: downloading file 3, Download data len 12064 [ 24.871697] Board extended Data download address: 0x0 [ 24.896621] ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 24.902636] [ 24.902636] Selecting OTP binary for CHIP Version 0 [ 24.909861] ol_transfer_bin_file 3623: downloading file 0, Download data len 4424 [ 24.932672] [ 24.932672] [Flash] : Ignore Module param [ 24.937650] [ 24.937650] Second otp download Param 10000 [ 24.953712] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 [ 24.960939] [ 24.960939] Mission mode: Firmware CHIP Version 0 [ 24.968406] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 [ 24.975923] Swap: bytes_left to copy: fw:16; dma_page:109113 [ 24.980585] Swap: wrong length read:0 [ 24.984841] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 153031 Target address 4172b0 [ 24.993330] scn=cc2404c0 target_write_addr=4172b0 seg_info=ccf60910 [ 24.999993] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 [ 25.008665] [wifi0] FWLOG: [30171] WAL_DBGID_TX_AC_BUFFER_SET ( [ 25.014151] bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin [ 25.024823] 0x3, 0x1e, 0x94c, 0x94c, 0x0 ) [ 25.028501] [wifi0] FWLOG: [30171] WAL_DBGID_TX_AC_BUFFER_SET ( [ 25.034612] ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin [ 25.043234] ol_transfer_bin_file 3623: downloading file 1, Download data len 364076 [ 25.050699] 0x12, 0x1e, 0x94c, 0x94c, 0x0 ) [ 25.054113] [wifi0] FWLOG: [30171] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 ) [ 25.062785] [wifi0] FWLOG: [30171] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 ) [ 26.296412] ol_target_init() Download FW done. [ 26.299990] ol_ath_attach() WMI attached. wmi_handle cc300000 [ 26.306298] htc_wmi_init() HT Create . cd2d2000 [ 26.310245] htc_wmi_init() HIF Claim. [ 26.314900] htc_wmi_init 7732 host_enable 0 nss_nwifi_offload 0 [ 26.319794] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) [ 26.329606] OL_ACBKMinfree : 0 [ 26.332292] OL_ACBEMinfree : 0 [ 26.335848] OL_ACVIMinfree : 0 [ 26.338541] OL_ACVOMinfree : 0 [ 26.346152] CE_recv_buf_enqueue 877 Populate last entry 512 for CE 5 [ 26.351482] CE_recv_buf_enqueue 886 CE 5 wi 511 dest_ptr 0x8bc15800 nbytes 0 recv_ctxt 0xcbc19700 [ 26.363005] Startup Mode-0 set [ 26.365471] [ 26.365471] <=== cfg max peer id 1056 ====> [ 26.371119] HTC Service:0x0300 ep:1 TX flow control disabled [ 26.377305] htt_peer_map_timer_init Enter pdev cbc78000 hrtimer cbc7a520 [ 26.383007] [ 26.383007] htt_alloc_peer_map_mem : Alloc Success : host q vaddr ccf94000 paddr 8cf94000 [ 26.393512] [ 26.393512] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 26.404048] CE_pkt_dl_len_set CE 4 Pkt download length 64 [ 26.408552] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from cbf60000 [ 26.418345] HTC Service:0x0100 ep:2 TX flow control disabled [ 26.424660] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 26.430471] Firmware_Build_Number:92 [ 26.434121] num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffa [ 26.444614] [ 26.444614] RES CFG Support wmi_service_bitmap 9778 [ 26.450479] Sending Ext resource cfg: HOST PLATFORM as 0 and fw_feature_bitmap as 50 to TGT [ 26.459593] ol_ath_service_ready_event: tt_support: 1 [ 26.464751] ol_ath_service_ready_event: periodic_chan_stats: 1 [ 26.470001] ol_ath_service_ready_event: sw_cal_support_check_flag: 1 [ 26.476749] Peer Caching Enabled ; num_peers = 257, num_active_peers = 52 num_tids = 104, num_vdevs = 17 [ 26.489881] Mesh Supported [ 26.491570] idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 [ 26.499788] ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, [ 26.507096] idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 [ 26.514879] ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, [ 26.522113] idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 [ 26.530503] ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, [ 26.537741] idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 258 [ 26.545598] ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 258 unit_len 744, [ 26.552757] idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 [ 26.561134] ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, [ 26.568400] idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 [ 26.576025] ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144, [ 26.583226] idx 6 req 5 num_units 0 num_unit_info 2 unit size 2044 actual units 258 [ 26.591585] ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 86 unit_len 2044, [ 26.598990] ol_ath_alloc_host_mem_chunk req_id 5 idx 7 num_units 86 unit_len 2044, [ 26.606561] ol_ath_alloc_host_mem_chunk req_id 5 idx 8 num_units 86 unit_len 2044, [ 26.613943] chunk 0 len 13568 requested ,ptr 0x8bf50000 [ 26.619074] chunk 1 len 54272 requested ,ptr 0x8bfc0000 [ 26.624836] chunk 2 len 217088 requested ,ptr 0x8b800000 [ 26.629924] chunk 3 len 191952 requested ,ptr 0x8b840000 [ 26.635765] chunk 4 len 107520 requested ,ptr 0x8bfe0000 [ 26.640861] chunk 5 len 6144 requested ,ptr 0x8bf16000 [ 26.646550] chunk 6 len 175784 requested ,ptr 0x8b880000 [ 26.651626] chunk 7 len 175784 requested ,ptr 0x8b8c0000 [ 26.657482] chunk 8 len 175784 requested ,ptr 0x8b900000 [ 26.662707] ol_ath_service_ready_event[4067] WAPI MBSSID 2 [ 26.704325] wmi_ready_event_rx: WMI UNIFIED READY event [ 26.708719] ol_ath_connect_htc() WMI is ready [ 26.713178] htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1 [ 26.728496] ol_ath_attach() connect HTC. [ 26.731472] bypasswmi : 0 [ 26.734119] target uses HTT version 2.2; host uses 2.2 [ 26.739727] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 26.751372] Skipping VHT80 channel 5825 [ 26.756748] acfg_attach: Offload using existing sock cdc1e800 [ 26.761490] SPECTRAL : get_capability not registered [ 26.767186] HAL_CAP_PHYDIAG : Capable [ 26.770056] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) [ 26.778533] SPECTRAL : get_capability not registered [ 26.783070] HAL_CAP_RADAR : Capable [ 26.787198] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 26.787198] (spectral_attach : 242) [ 26.796997] SPECTRAL : get_capability not registered [ 26.801514] HAL_CAP_SPECTRAL_SCAN : Capable [ 26.806051] SPECTRAL : get_tsf64 not registered [ 26.810158] spectral_init_netlink 78 NULL SKB [ 26.815109] Green-AP : Green-AP : Attached [ 26.815109] [ 26.820087] Green-AP : Attached [ 26.823178] rate power table override is only supported for AR98XX [ 26.830677] ol_if_dfs_attach: called; ptr=cbfd1984, radar_info=cdf69c48 [ 26.836688] dfs_attach: event log enabled by default [ 26.842985] ipq4019_wifi_led_init: Wifi LED init failed.. Couldn't get led gpio/led source [ 26.851215] ol_ath_attach() UMAC attach . [ 26.854708] [ 26.854708] BURSTING enabled by default [ 26.860517] ACS not enabled [ 26.862627] __ol_ath_attach: needed_headroom reservation 60 [ 26.877352] ol_ath_thermal_mitigation_attach: -- [ 26.893915] ath_ol_pci: (Atheros/multi-bss) [ 26.897257] ol_ath_pci_probe: PCI device id 0050 :0050 [ 26.902291] PCI: enabling device 0000:00:00.0 (0144 -> 0147) [ 26.941976] PCI: enabling device 0000:01:00.0 (0140 -> 0142) [ 26.947240] *********** Peregrine ************** [ 26.951326] __ol_ath_attach: Creating netdev wifi2 [ 26.964378] [ 26.964378] __ol_ath_attach() Allocated scn cba004c0 [ 26.971536] ath_ol_pci 0000:01:00.0: ath DEBUG: sc=0xcc20e400 [ 26.977010] [ 26.977010] ol_ath_pci_configure : num_desired MSI set to 0 [ 26.983395] [ 26.983395] Using PCI Legacy Interrupt [ 27.319579] [wifi1] FWLOG: [32546] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 ) [ 27.327153] [wifi1] FWLOG: [32546] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 ) [ 27.335835] [wifi1] FWLOG: [32546] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 ) [ 27.344512] [wifi1] FWLOG: [32546] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 ) [ 27.382420] Switching to Tx Mode-1 Threshold 280 [ 27.993189] [ 27.993189] CLOCK PLL skipped [ 27.999501] __ol_ath_attach: dev name wifi2 [ 28.002659] ol_ath_attach interface_id 2 [ 28.007413] ol_target_init() BMI inited. [ 28.010618] ol_target_init() BMI Get Target Info. [ 28.015648] Chip id: 0x7, chip version: 0x4100016d [ 28.019925] [ 28.019925] CE WAR Disabled [ 28.024957] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 28.029827] ol_target_init() configure Target . [ 28.034901] ol_transfer_bin_file: flash data file defined [ 28.039583] ol_transfer_bin_file[3752] Get Caldata for wifi2. [ 28.045753] __adf_os_fs_read[42], Open File /tmp/wifi2.caldata SUCCESS!! [ 28.051955] file system magic:16914836 [ 28.056202] super blocksize:4096 [ 28.059073] inode 1157 [ 28.061503] file size:12064 [ 28.065043] __adf_os_fs_read[55]: caldata data size mismatch, fsize=12064, cal_size=2116 [ 28.072501] ol_transfer_bin_file 3813: Download Flash data len 2116 [ 28.079293] Board extended Data download address: 0x0 [ 28.087852] ol_download_cal_data: Board data file: 4 successfully downloaded, download address: 00401cc0 [ 28.096869] [ 28.096869] Mission mode: Firmware CHIP Version 0 [ 28.102691] ol_transfer_bin_file: Downloading firmware file: AR9887/athwlan.bin [ 28.516508] ol_transfer_bin_file 3623: downloading file 1, Download data len 230420 [ 29.085911] [ 29.085911] !!!!! {/usr/bin/client_eventd} failed writing /click/client_ip_table/madwifi_clients len 0 data: "" [ 29.525317] ol_target_init() Download FW done. [ 29.528884] ol_ath_attach() WMI attached. wmi_handle cb9f0000 [ 29.535371] htc_wmi_init() HT Create . cd2d3800 [ 29.539191] htc_wmi_init() HIF Claim. [ 29.542867] htc_wmi_init 7732 host_enable 1 nss_nwifi_offload 0 [ 29.549377] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) [ 29.558413] OL_ACBKMinfree : 0 [ 29.561195] OL_ACBEMinfree : 0 [ 29.564979] OL_ACVIMinfree : 0 [ 29.567480] OL_ACVOMinfree : 0 [ 29.574857] CE_recv_buf_enqueue 877 Populate last entry 512 for CE 5 [ 29.580184] CE_recv_buf_enqueue 886 CE 5 wi 511 dest_ptr 0x8bb9aa80 nbytes 0 recv_ctxt 0xcbb54400 [ 29.590027] Startup Mode-0 set [ 29.592074] [ 29.592074] <=== cfg max peer id 1056 ====> [ 29.598968] HTC Service:0x0300 ep:1 TX flow control disabled [ 29.604199] htt_peer_map_timer_init Enter pdev cbba0000 hrtimer cbba2520 [ 29.610288] [ 29.610288] htt_alloc_peer_map_mem : Alloc Success : host q vaddr ccf95000 paddr 8cf95000 [ 29.620623] [ 29.620623] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 29.631524] CE_pkt_dl_len_set CE 4 Pkt download length 64 [ 29.636416] ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from cb650000 [ 29.644783] HTC Service:0x0100 ep:2 TX flow control disabled [ 29.650392] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 29.656606] Firmware_Build_Number:0 [ 29.659766] host/RAM_fw Build Ver Mismatch: H:0x5C, F:0x0 ! [ 29.666047] num_rf_chain:0x00000001 ht_cap_info:0x0000085b vht_cap_info:0x338001b2 vht_supp_mcs:0x0000fffe [ 29.675592] [ 29.675592] RES CFG Support wmi_service_bitmap 874a [ 29.681821] Sending Ext resource cfg: HOST PLATFORM as 1 and fw_feature_bitmap as 50 to TGT [ 29.690776] ol_ath_service_ready_event: tt_support: 0 [ 29.696151] ol_ath_service_ready_event: periodic_chan_stats: 1 [ 29.701363] Switching to Tx Mode-1 Threshold 280 [ 29.706389] ol_ath_service_ready_event: sw_cal_support_check_flag: 0 [ 29.712285] LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256 [ 29.719358] idx 0 req 1 num_units 0 num_unit_info 2 unit size 404 actual units 145 [ 29.726944] ol_ath_alloc_host_mem_chunk req_id 1 idx 0 num_units 145 unit_len 404, [ 29.734425] chunk 0 len 58580 requested ,ptr 0x8b670000 [ 29.746430] FIRMWARE:P 145 V 16 T 443 [ 29.746430] [ 29.751640] wmi_ready_event_rx: WMI UNIFIED READY event [ 29.756335] ol_ath_connect_htc() WMI is ready [ 29.760400] htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 2 [ 29.776011] ol_ath_attach() connect HTC. [ 29.778987] bypasswmi : 0 [ 29.781597] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 29.793356] target uses HTT version 2.2; host uses 2.2 [ 29.799867] Skipping VHT80 channel 5825 [ 29.804378] acfg_attach: Offload using existing sock cdc1e800 [ 29.809122] SPECTRAL : get_capability not registered [ 29.814806] HAL_CAP_PHYDIAG : Capable [ 29.817684] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) [ 29.826410] SPECTRAL : get_capability not registered [ 29.830737] HAL_CAP_RADAR : Capable [ 29.834782] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 29.834782] (spectral_attach : 242) [ 29.844544] SPECTRAL : get_capability not registered [ 29.849103] HAL_CAP_SPECTRAL_SCAN : Capable [ 29.853272] SPECTRAL : get_tsf64 not registered [ 29.858467] spectral_init_netlink 78 NULL SKB [ 29.862169] Green-AP : Green-AP : Attached [ 29.862169] [ 29.868214] Green-AP : Attached [ 29.870977] ol_if_dfs_attach: called; ptr=cb6b1984, radar_info=cdf69c08 [ 29.878073] dfs_attach: event log enabled by default [ 29.884863] ol_ath_attach() UMAC attach . [ 29.888026] [ 29.888026] BURSTING enabled by default [ 29.893443] ACS not enabled [ 29.896940] __ol_ath_attach: hard_header_len reservation 74 [ 29.909827] ol_ath_thermal_mitigation_attach: TT not supported in FW [ 30.163787] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 30.201024] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 30.224177] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 [ 30.230401] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 [ 30.251051] pktlog_init: Initializing Pktlog for AR9888, pktlog_hdr_size = 12 [ 30.537182] [ 30.537182] !!!!! {/usr/bin/brain} opening /click/wlan_event/driver_reload failed: No such file or directory [ 30.549804] [wifi2] FWLOG: [30148] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x460, 0x460, 0x0 ) [ 30.565376] [wifi2] FWLOG: [30148] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x460, 0x460, 0x0 ) [ 30.583664] [wifi2] FWLOG: [30148] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x460, 0x460, 0x0 ) [ 30.591641] [wifi2] FWLOG: [30148] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x460, 0x460, 0x0 ) [ 30.609338] [wifi2] FWLOG: [30150] WHAL_ERROR_RESET_PM ( ) [ 30.623649] [wifi2] FWLOG: [30154] WAL_DBGID_DEV_RESET ( 0x1, 0x1, 0x1 ) [ 32.868531] brain: unloading click config [ 32.871859] brain: spring cleaning pages [ 34.388013] [ol_ath_iw_setcountry][1733] *p=55, *(p+1)=53 [ 34.392400] isCountryCodeValid: EEPROM regdomain 0x0 [ 34.720425] wlan_vap_create : enter. devhandle=0xcd2804c0, opmode=IEEE80211_M_HOSTAP, flags=0x0 [ 34.729083] ieee80211_mbo_vattach:MBO Initialized [ 34.737408] wlan_vap_create : exit. devhandle=0xcd2804c0, vap=0xcb778000, opmode=IEEE80211_M_HOSTAP, flags=0x0. [ 35.152986] ieee80211_mbo_vattach:MBO Initialized [ 35.218455] ieee80211_mbo_vattach:MBO Initialized [ 35.281742] ieee80211_mbo_vattach:MBO Initialized [ 35.342629] ieee80211_mbo_vattach:MBO Initialized [ 35.401883] ieee80211_mbo_vattach:MBO Initialized [ 35.460980] ieee80211_mbo_vattach:MBO Initialized [ 35.519587] ieee80211_mbo_vattach:MBO Initialized [ 35.599622] ieee80211_mbo_vattach:MBO Initialized [ 35.666161] ieee80211_mbo_vattach:MBO Initialized [ 35.726154] ieee80211_mbo_vattach:MBO Initialized [ 35.793201] ieee80211_mbo_vattach:MBO Initialized [ 35.852311] ieee80211_mbo_vattach:MBO Initialized [ 35.912079] ieee80211_mbo_vattach:MBO Initialized [ 35.971442] ieee80211_mbo_vattach:MBO Initialized [ 36.030912] ieee80211_mbo_vattach:MBO Initialized [ 36.035734] ol_txrx_set_mesh_mode val 1 [ 36.091147] wlan_vap_create : enter. devhandle=0xcd2804c0, opmode=IEEE80211_M_MONITOR, flags=0x0 [ 36.100584] wlan_vap_create : exit. devhandle=0xcd2804c0, vap=0xcb130000, opmode=IEEE80211_M_MONITOR, flags=0x0. [ 36.175488] [ol_ath_iw_setcountry][1733] *p=55, *(p+1)=53 [ 36.179876] isCountryCodeValid: EEPROM regdomain 0x0 [ 36.185603] Skipping VHT80 channel 5825 [ 36.204571] wlan_vap_create : enter. devhandle=0xcc2404c0, opmode=IEEE80211_M_HOSTAP, flags=0x0 [ 36.212657] ieee80211_mbo_vattach:MBO Initialized [ 36.217904] wlan_vap_create : exit. devhandle=0xcc2404c0, vap=0xcb188000, opmode=IEEE80211_M_HOSTAP, flags=0x0. [ 36.282509] ieee80211_mbo_vattach:MBO Initialized [ 36.371780] ieee80211_mbo_vattach:MBO Initialized [ 36.456124] ieee80211_mbo_vattach:MBO Initialized [ 36.532368] ieee80211_mbo_vattach:MBO Initialized [ 36.616653] ieee80211_mbo_vattach:MBO Initialized [ 36.687642] ieee80211_mbo_vattach:MBO Initialized [ 36.771354] ieee80211_mbo_vattach:MBO Initialized [ 36.846323] ieee80211_mbo_vattach:MBO Initialized [ 36.926025] ieee80211_mbo_vattach:MBO Initialized [ 37.010706] ieee80211_mbo_vattach:MBO Initialized [ 37.113200] ieee80211_mbo_vattach:MBO Initialized [ 37.193122] ieee80211_mbo_vattach:MBO Initialized [ 37.277697] ieee80211_mbo_vattach:MBO Initialized [ 37.371252] ieee80211_mbo_vattach:MBO Initialized [ 37.466101] ieee80211_mbo_vattach:MBO Initialized [ 37.470338] ol_txrx_set_mesh_mode val 1 [ 37.555551] wlan_vap_create : enter. devhandle=0xcc2404c0, opmode=IEEE80211_M_MONITOR, flags=0x0 [ 37.592657] wlan_vap_create : exit. devhandle=0xcc2404c0, vap=0xcb340000, opmode=IEEE80211_M_MONITOR, flags=0x0. [ 38.045569] brain: loading click config [ 41.631343] Click Queue signal cb registration failed! [ 42.422557] OL vap_start - [ 42.446881] vap-15(mesh0):set SIOC80211NWID, 9 characters [ 42.451253] [ 42.451253] DES SSID SET=fast-mesh [ 42.477636] Setting Tx Encap type to 0 (Raw) [ 42.487282] Setting Rx Decap type to 0 (Raw) [ 42.576629] OL vap_start - [ 42.596781] vap-15(mesh1):set SIOC80211NWID, 9 characters [ 42.601151] [ 42.601151] DES SSID SET=fast-mesh [ 42.627913] Setting Tx Encap type to 0 (Raw) [ 42.644952] Setting Rx Decap type to 0 (Raw) [ 43.016942] [wifi0] FWLOG: [48654] WAL channel change freq=2412, mode=2 flags=0 rx_ok=1 tx_ok=1 [ 43.030824] [ol_ath_iw_setcountry][1733] *p=55, *(p+1)=53 [ 43.043829] isCountryCodeValid: EEPROM regdomain 0x0 [ 43.054183] Skipping VHT80 channel 5825 [ 43.089068] wlan_vap_create : enter. devhandle=0xcba004c0, opmode=IEEE80211_M_HOSTAP, flags=0x1001 [ 43.108870] ieee80211_mbo_vattach:MBO Initialized [ 43.112709] enabling promiscuos bit [ 43.134235] wlan_vap_create : exit. devhandle=0xcba004c0, vap=0xcbcb0000, opmode=IEEE80211_M_HOSTAP, flags=0x1001. [ 43.196281] vap-0(mon2):set SIOC80211NWID, 10 characters [ 43.200644] [ 43.200644] DES SSID SET=specialvap [ 43.312558] [wifi1] [ 43.313972] OL vap_start - [ 43.316530] FWLOG: [48812] WAL channel change freq=5180, mode=0 flags=0 rx_ok=1 tx_ok=1 [ 43.333672] ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 [ 43.341052] ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 [ 43.391767] [ 43.391767] !!!!! {/usr/bin/config_updater} starting upgrade to version "29-202206221456-Gd67aaf64-L84d26691-jenkins-rel-opposite" [ 43.408373] device wifi2 entered promiscuous mode [ 43.550767] [wifi2] FWLOG: [43832] WHAL_ERROR_RESET_CHANNF1 ( ) [ 43.579838] [ 43.579838] DES SSID SET= [ 43.594560] [ 43.594560] DES SSID SET= [ 43.958098] [ 43.958098] DES SSID SET= [ 43.965267] [ 43.965267] DES SSID SET= [ 44.182609] [ 44.182609] DES SSID SET= [ 44.187945] [ 44.187945] DES SSID SET= [ 44.297316] [ 44.297316] DES SSID SET= [ 44.301549] [ 44.301549] DES SSID SET= [ 44.384810] [ 44.384810] DES SSID SET= [ 44.389618] [ 44.389618] DES SSID SET= [ 44.503926] [ 44.503926] DES SSID SET= [ 44.507853] [ 44.507853] DES SSID SET= [ 44.595516] [ 44.595516] DES SSID SET= [ 44.599852] [ 44.599852] DES SSID SET= [ 44.713379] [ 44.713379] DES SSID SET= [ 44.718270] [ 44.718270] DES SSID SET= [ 44.811448] [ 44.811448] DES SSID SET= [ 44.816756] [ 44.816756] DES SSID SET= [ 44.929210] [ 44.929210] DES SSID SET= [ 44.934713] [ 44.934713] DES SSID SET= [ 45.023802] [ 45.023802] DES SSID SET= [ 45.027740] [ 45.027740] DES SSID SET= [ 45.135304] [ 45.135304] DES SSID SET= [ 45.139882] [ 45.139882] DES SSID SET= [ 45.232833] [ 45.232833] DES SSID SET= [ 45.237667] [ 45.237667] DES SSID SET= [ 45.346402] [ 45.346402] DES SSID SET= [ 45.350663] [ 45.350663] DES SSID SET= [ 45.451802] [ 45.451802] DES SSID SET= [ 45.457119] [ 45.457119] DES SSID SET= [ 72.734782] CPU1: Booted secondary processor [ 72.734835] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 72.764729] CPU2: Booted secondary processor [ 72.764780] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 72.776316] CPU3: Booted secondary processor [ 72.776383] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 73.151366] [ 73.151366] !!!!! {/usr/bin/brain} forkexec failed with status 255 cmd -iwpriv mon0 packet_counter 0 [ 73.166111] [ 73.166111] !!!!! {/usr/bin/brain} forkexec failed with status 255 cmd -iwpriv mon1 packet_counter 0 [ 73.180682] [ 73.180682] !!!!! {/usr/bin/brain} forkexec failed with status 255 cmd -iwpriv mon2 packet_counter 0 [ 73.196029] device wired0 entered promiscuous mode [ 73.203791] device wired1 entered promiscuous mode [ 73.221936] [ 73.221936] !!!!! {/usr/bin/brain} forkexec failed with status 255 cmd -iwpriv wifi0 acktimeout 48 [ 73.236252] [ 73.236252] !!!!! {/usr/bin/brain} forkexec failed with status 255 cmd -iwpriv wifi1 acktimeout 48 [ 73.299313] Resetting spectral chainmask to Rx chainmask [ 73.299682] [wifi1] FWLOG: [80099] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x2 ) [ 73.299692] [wifi1] FWLOG: [80099] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x3 ) [ 73.329798] Resetting spectral chainmask to Rx chainmask [ 73.757919] wmi_dbg_cfg_send: mod[0]00000000 dbgcfg50000000 cfgvalid[0] 00000000 cfgvalid[1] 00000000 [ 73.770167] cfg valid value inside module enable 400000wmi_dbg_cfg_send: mod[0]00000000 dbgcfg00000000 cfgvalid[0] 00400000 cfgvalid[1] 00000000 [ 73.786600] wmi_dbg_cfg_send: mod[0]00000000 dbgcfg50000000 cfgvalid[0] 00000000 cfgvalid[1] 00000000 [ 73.798994] cfg valid value inside module enable 400000wmi_dbg_cfg_send: mod[0]00000000 dbgcfg00000000 cfgvalid[0] 00400000 cfgvalid[1] 00000000



This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2025/07/23 06:32
  • by hmartin